Product Overview

A maintenance kit of CH440 spare parts — the supporting components that sit around the crushing chamber of the CH440 / H4800 cone crusher: the head nut and burn ring that clamp the mantle on the cone head, the dust and oil seal rings and O-rings that keep dust out of the eccentric and lubrication circuits, the spider bushing and spider cap that locate and protect the top of the main shaft, the main shaft sleeve, and the hydraulic filter cartridges and spin-on filter element that protect the lubrication system.

These are the parts normally ordered alongside a liner change or scheduled overhaul. They are supplied together so a shutdown can be completed in one pass without waiting on individual components, and so seal and filter items are replaced at the right interval rather than being reused past their service life.

CH440 Spare Parts List

Equipment Overview

The CH440 (also designated H4800) is a hydrocone-style secondary or tertiary cone crusher used in aggregate production, quarrying, mining and recycling. Around the crushing chamber, a number of support, sealing and filtration components keep the machine running between liner changes: the head nut and burn ring lock the mantle onto the cone head; the dust seal ring y oil seal ring separate the crushing chamber from the eccentric and lubrication spaces; the spider bushing y spider cap take the top bearing load of the main shaft; and the filter cartridges keep the lubrication oil clean. Neglecting these items is a common cause of premature bearing wear, oil contamination and unplanned downtime.

Component Notes

• Tuerca de cabeza con anillo quemado — clamps the mantle down on the cone head; the burn ring backs the nut so it cannot loosen under crushing load.
• Dust Seal Ring / Oil Seal Ring / O-Ring / Seal Ring — the sealing set that stops rock dust reaching the eccentric and stops lubrication oil escaping. Seal items should be replaced at every liner change rather than reused.
• Casquillo de araña — the upper bearing surface that steadies the top of the main shaft inside the spider.
• Gorra araña — covers and retains the spider bore, keeping dust and water out of the top bearing.
• Manguito del eje principal — protects the main shaft where it passes through the sealing and bearing areas.
• Filter Cartridges and Spin-On Filter Element — protect the lubrication circuit; a clogged element raises oil temperature and accelerates wear on the eccentric and gears.
• Hydraulic Pump, Hydroset Relief Valve and Pressure Indicator — the hydroset circuit that sets and holds the closed-side setting: the pump moves the oil, the relief valve protects the circuit from over-pressure, and the pressure indicator (PIS 3097, 2.2 bar) shows the clamping pressure directly on the machine.

Aplicaciones

Scheduled maintenance and liner changes on CH440 / H4800 cone crushers in quarry, mining and recycling plants, plus the equivalent CH420 and CH430 filter elements where the same lubrication circuit is used. Keeping the correct sealing and filtration components in stock is what keeps a cone crusher available through the crushing season.

Related CH440 Spare Parts and Crusher Wear Parts

• CH440 / H4800 concave 442.8421 and mantle B 442.7230 — the crushing chamber wear parts normally replaced at the same shutdown.
• Cone crusher bowl liner, concave ring and torch ring for other hydrocone and cone crusher models.
• Cone crusher assembly and spare parts — eccentric, main shaft, step washer and adjustment components.
• Swing and stationary jaw plates for mobile jaw crushers (QJ341 and similar).

Request a Quotation

For pricing, lead time and availability on these CH440 spare parts — head nut, dust and oil seal rings, spider bushing and cap, main shaft sleeve and filter cartridges — please use the Añadir a la consulta button on this page or email us at [email protected]. Our sales team responds within one business day.

The post CH440 H4800 Cone Crusher Spare Parts Kit Head Nut Seal Rings Spider Bushing Cap and Filters appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Product Overview

Matched wear parts for the CH440 / H4800 cone crusher: the 440 concave (442.8421) and the B-profile mantle (442.7230). Both are cast in M7 high manganese steel and machined on the seating and clamping faces so the cone head and upper frame locate correctly, keeping the closed-side setting and chamber geometry within specification.

Wear Parts List

Material and Casting

• M7 high manganese steel — the M7 grade is a work-hardening austenitic manganese casting (Mn18Cr2 type) that develops a hard wearing surface under load while the core stays tough enough to pass tramp metal. The grade is stamped on each casting for traceability.
• Water-glass sand casting with controlled heat treatment for a uniform austenitic structure.
• Machined seating and clamping faces so the concave beds down square in the frame and the mantle seats correctly on the cone head.
• B-profile cavity geometry matched to the original chamber specification.

Aplicaciones

Suited to secondary and tertiary crushing of granite, basalt, limestone, river gravel, iron ore and construction and demolition waste. Replacing mantle and concave as a matched set avoids eccentric wear and keeps the setting stable through the wear cycle.

Request a Quotation

For pricing and lead time on the CH440 / H4800 wear parts (442.8421 concave and 442.7230 mantle B) in M7 material, use the Añadir a la consulta button or email [email protected].

The post 442.8421 Concave Ring 442.7230 Mantle B for CH440 H4800 Cone Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Product Overview

A matched pair of crushing jaws for the QJ341 mobile jaw crusher (C12 jaw unit): the corrugated swing jaw (J2950000) and the stationary jaw plate (400.0436). Both are cast in M7 high manganese steel and machined on the seating faces so they pull down flat against the jaw stock and frame, keeping the crushing gap and nip angle within specification.

The corrugated profile on the swing jaw works against the stationary plate to grip and compress the feed, so the two faces wear as a pair. Supplying them together keeps the tooth profiles matched and the reduction ratio consistent through the wear cycle.

Wear Parts List

Equipment Overview

The QJ341 is a track-mounted mobile jaw crusher built around a single-toggle C12 jaw unit, widely used as a primary crusher in quarrying, mining, demolition and recycling. Material is fed between a stationary jaw plate fixed to the crusher frame and a swing jaw carried on the jaw stock, driven by the eccentric shaft. Tooth geometry and jaw profile control the nip angle, throughput and the shape of the primary product, so worn plates directly affect both capacity and downstream screening efficiency.

Material and Casting

• M7 high manganese steel — the M7 grade is a work-hardening austenitic manganese casting (Mn18Cr2 type) that develops a hard wearing surface under impact while the core remains tough enough to pass uncrushable material. The grade is stamped on each casting for traceability.
• Water-glass sand casting with controlled heat treatment to produce a uniform austenitic structure.
• Machined seating faces and matched bolt-hole pattern so both jaws bed down correctly and the wedges load evenly.
• Corrugated tooth profile matched to the original jaw geometry for correct nip and grip on slabby or rounded feed.

Aplicaciones

Suited to primary crushing in hard rock quarries, mining operations, construction and demolition recycling, and aggregate production — granite, basalt, limestone, river gravel and demolition debris. Jaw wear life depends on feed size, material abrasiveness and the closed-side setting; fitting the swing and stationary jaws as a matched pair keeps both faces wearing evenly.

Related Parts Available

• CJ411 toggle plate and toggle seat for the same jaw crusher family
• CJ411 wedge plate (fixed / swing, 4 pcs per set)
• Swing and stationary jaw plates for other mobile jaw crushers in M7 (Mn18Cr2) and Mn22Cr2 grades

Request a Quotation

For pricing, lead time and availability on the QJ341 jaw wear parts (J2950000 corrugated swing jaw and 400.0436 stationary jaw plate) in M7 material, please use the Añadir a la consulta button on this page or email us at [email protected]. Our sales team responds within one business day.

The post J2950000 Swing Jaw Corrugated 400.0436 Stationary Jaw Plate for QJ341 Mobile Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Product Overview

This is a complete wedge assembly set for the TP450 cone crusher, comprising the wedge body together with its matching bolts and nuts — the components that clamp and secure the mantle and bowl liner in the crushing chamber. Manufactured by MiningSpares from cast steel with a durable painted finish, the set is supplied as a matched kit so that the wedge, bolt and nut threads are fully compatible and fasten correctly under load.

Wedge Assembly Components

Equipment Overview

The TP450 is a heavy-duty cone crusher widely used in mining, quarrying and aggregate production for secondary and tertiary crushing of hard rock and ores. Inside the crushing chamber, the mantle is mounted on the main shaft and the bowl liner is held in the upper frame; both are locked in position by a ring of wedge assemblies. Each wedge presses the liner against its seating face, while the bolt and nut clamp the wedge in place and maintain the preload as the machine operates.

Why the Wedge Set Matters

• Correct liner clamping — a worn or loose wedge lets the mantle or bowl liner shift, causing uneven wear, poor product shape and possible damage to the frame seating faces.
• Matched kit — wedge, bolt and nut are supplied together so thread pitch, hardness and geometry are compatible and torque correctly.
• Service accessibility — the wedge design allows liner changes to be carried out with standard tooling during scheduled maintenance shutdowns.
• Corrosion protection — the painted finish limits rust during storage and shipment, keeping the assembly free-running at installation.

Typical Applications

The TP450 cone crusher and its wedge assembly set are used in hard rock mining operations, stone quarries, sand and gravel plants, cement and industrial mineral processing, and construction and demolition recycling — wherever secondary or tertiary crushing of abrasive material is required.

Related Parts Available

• TP450 TIC composite bowl liner and mantle set (TRIO17023515 / TRIO17023516)
• TP450 concave ring and mantle (Mn18Cr2 / Mn22Cr2)
• Bowl liner, mantle, concave segments and locking components for the TP450 cone crusher

Request a Quotation

For pricing, lead time and availability on the TP450 wedge assembly set (TRIO17026581 with TRIO17023529 bolt and TRIO17023527 nut), please use the Añadir a la consulta button on this page or email us at [email protected]. Our sales team responds within one business day.

The post TRIO17026581 Wedge Assembly with Bolt and Nut for TP450 Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

High-manganese swing and fixed jaw plates manufactured by MiningSpares for the СМД-111
(SMD111) jaw crusher – the Russian-built primary jaw crusher also designated
ЩДП-9х12 and originally produced by Volgotsemmash (ОАО «Волгоцеммаш»).
The set consists of three cast manganese plates that form the primary crushing chamber: an upper and a lower
swing (movable) jaw plate running on the pitman, plus the stationary fixed jaw plate. Each plate is cast,
heat-treated and machined to drawing for direct replacement, with no frame modification required.

СМД-111 Jaw Plate Specification Table

Item 3 (3440.01.110) is a 2-piece (2P) fixed jaw plate design.

Material & Casting Process

All three plates are cast in Mn18% high-manganese steel (austenitic manganese steel,
equivalent to ASTM A128 Grade B2 / GOST 977-88 grade 110Г13Л) using water-glass sand casting. Each casting
is solution heat-treated (water quenched) to deliver a fully austenitic structure, then precision-machined on
all mating and seating faces so it seats correctly against the СМД-111 crusher frame and pitman.

• As-cast hardness: HB 200–220
• Work-hardened surface hardness in service: HB 450+
• Key benefit: the more the plate is impacted, the harder the working surface becomes –
  ideal for the high-compression duty of a primary jaw chamber

Machine Data – СМД-111 (ЩДП-9х12)

For fitment confirmation, the host machine data published by the original manufacturer:

• Designation: СМД-111 / ЩДП-9х12
• Feed opening (width × length): 900 × 1200 mm
• Maximum feed lump size: 750 mm
• Overall dimensions (L × W × H): 4,942 × 3,150 × 3,300 mm (excluding drive)
• Machine mass (less components): 54.3 t
• Application: primary crushing of granite, basalt, quartzite, sandstone, limestone and ores
  with a compressive strength up to 300 MPa

Aplicaciones

СМД-111 jaw plates are used for primary crushing in hard-rock mining, quarry and aggregate production,
and construction-recycling duties – typically granite, gabbro, basalt and diabase duty in Russian and
CIS crushing plants.

Frequently Asked Questions

Q1. What material grade are the plates supplied in?
Mn18% high-manganese steel as standard. Mn18Cr2 and Mn13Cr2 are available on request for highly abrasive
or high-impact duties.

Q2. Can I buy a single plate rather than the full set?
Yes. Each of the three plates can be ordered separately – just quote the drawing number(s) from the table
above when enquiring.

Q3. What is the lead time?
Machined plates from stock: 7–10 working days. Fresh castings: 25–35 days. Breakdown orders can be
expedited and shipped by airfreight.

Q4. What documentation is supplied?
Every shipment includes spectrometer chemical-composition report, hardness test report and dimensional
inspection report. Third-party inspection (SGS, BV, TÜV) can be arranged on request.

Q5. Is this an OEM part?
No. These are aftermarket replacement parts manufactured by MiningSpares to the original drawings. They are
not affiliated with, or endorsed by, the original equipment manufacturer.

Request a Quotation

For pricing, lead time and alternative material grades on СМД-111 (SMD111) jaw plates, use the
Añadir a la consulta button on this page or email us at
[email protected]. Our sales team responds within one business day.

The post 3440.02.010 / 3440.02.020 / 3440.01.110 Jaw Plates for Russian SMD111 Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

High manganese Mn18Cr2 fixed and swing jaw plates manufactured by MiningSpares for Metso Nordberg C106 jaw crushers. Each casting is produced in our own foundry, heat-treated for work-hardening performance and precision-machined on all mating faces to OEM specifications, providing a direct drop-in replacement for the original Metso parts.

Specification Table – Metso C106 Jaw Plate Set

About the Metso Nordberg C106 Jaw Crusher

The Metso Nordberg C106 is a compact primary jaw crusher designed for hard rock and recycle applications in mining, quarry and aggregate operations. With a 1060 × 700 mm (42 × 28 in) jaw opening, the C106 delivers high throughput in a small footprint and is widely used as a primary stage in both stationary and track-mounted plants. The key wear parts in the C106 are the fixed and swing jaw plates – the components that MiningSpares supplies in Mn18Cr2 high manganese steel under drawing numbers MM0273923 and MM0273924.

Why MiningSpares Metso C106 Jaw Plates

• Cast in our own foundry using premium Mn18Cr2 high manganese steel
• Heat treatment optimised for work-hardening under impact in primary crushing
• Precision machined to OEM drawing tolerances on back face and bolt-hole pattern
• Direct replacement for the original Metso parts MM0273923 and MM0273924
• Stock availability for standard C106 jaw plate sets in Mn18Cr2 grade
• Custom material grades available on request (Mn14, Mn22Cr2, modified manganese)

Compatible Equipment

Metso Nordberg C106 jaw crusher and similar Metso C-series primary jaw crushers. Drawing numbers covered on this page: MM0273923 (fixed jaw plate, 2 pieces per crusher set) and MM0273924 (swing jaw plate, 1 piece per crusher set).

Manufacturing Process

Our Metso C106 fixed and swing jaw plates are produced through water-glass sand casting, followed by a controlled heat treatment cycle to develop the work-hardening austenitic manganese structure. Each plate is then precision-machined on the back face, bolt-hole pattern and edge profile to ensure a perfect fit with the C106 jaw crusher frame and to match the original swing geometry of the machine.

Aplicaciones

Metso C106 jaw plates are used in primary crushing of granite, basalt, gneiss, quartzite, iron ore, copper ore, gold ore, limestone and other medium-hard to hard rock. Typical installations include hard rock mining operations, quarries, aggregate production, and construction and demolition recycling.

Related Crusher Wear Parts

Browse more high manganese crusher wear parts from MiningSpares:

• PYB1200 Bowl Liner and Mantle
• MX4 Bowl Liner C for Cone Crusher
• H8800 Revestimiento hidrocónico
• Boratas SDK111 Jaw Plate Wear Parts

Request a Quotation

For pricing, lead time and material options on Metso C106 jaw plates MM0273923 and MM0273924, please use the Añadir a la consulta button on this page or email us at [email protected]. Our sales team will respond within one business day.

The post MM0273923 Fixed Jaw Quarry MM0273924 Swing Jaw Quarry For C106 Jaw appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

The assembly reference number (TRIO TRIO17001140) corresponds to chapter 1.6 HEAD AND MAIN SHAFT ASSEMBLY of the TC84X Parts Manual and contains 7 line items as listed below. Each part can be supplied individually or as a complete short-head main-shaft assembly; please quote the TRIO part number(s) when ordering.

Aftermarket replacement parts compatible with TC84X cone crusher. Not affiliated with or endorsed by the original equipment manufacturer.

1.6 Head and Main Shaft Assembly (Short Head) — TRIO17001140

Typical Applications

The TC84X short-head main-shaft assembly is used in secondary and tertiary crushing circuits where a finer product gradation is required. Compared with the standard (coarse-cavity) head, the short-head profile produces a higher proportion of finished-size particles in a single pass, making it the preferred cavity for:

• Hard-rock aggregate production (granite, basalt, diabase, gneiss)
• Iron-ore and copper-ore beneficiation plants (fine crushing stage)
• Recycled-aggregate and construction & demolition (C&D) processing lines
• Cement and lime-stone preparation circuits feeding ball mills

The head and main-shaft assembly is the rotating heart of the crusher and works in conjunction with the bowl assembly (chapter 1.7, TRIO5007838) to set the closed-side discharge opening. Inspection of the head casting, main shaft and mainshaft cap is recommended every 2,000 operating hours or whenever the mantle is replaced.

Frequently Asked Questions

Q1. What material is the main shaft (TRIO17001147) made of?
Forged from 40CrNiMo alloy steel, quenched and tempered to a typical hardness of 280–320 HB. Ultrasonic testing (UT) is performed on every forging before machining, and a test certificate is shipped with the part.

Q2. Can CASTEEL supply the head casting (TRIO17001142) and the cap (TRIO17001146) separately?
Yes. Both items are available as individual castings, with or without finish-machining. We can also supply them as a matched pair already fitted with the seal ring.

Q3. Is this assembly compatible with both TC84X and TC84XR models?
Yes. TRIO17001140 is the short-head main-shaft assembly for the TC84X platform; the same assembly fits the equivalent TC84XR model year — the TC84X / TC84XR naming is a commercial designation only. When ordering, simply quote the TRIO part number(s) shown in the table above.

Q4. What is the typical lead time?
Standard lead time is 30–45 days for castings + 15–20 days for machining. Stocked main shafts and caps can be dispatched within 7–10 working days for urgent breakdown orders.

Q5. Do you provide a quality / test package?
Yes. Every shipment includes the material test certificate (MTC), UT report, dimensional inspection report, and a warranty certificate. Third-party inspection (SGS, BV, TUV) can be arranged on request.

About CASTEEL MiningSpares

CASTEEL MiningSpares (est. 2003) is a Chinese foundry and machining supplier specialising in after-market wear and structural parts for cone, jaw, gyratory, VSI and hammer crushers. We hold ready stock of common TC84X and TC84XR line items and can tool up new patterns within 30 days for less common parts. All castings are produced in our own foundry under ISO 9001:2015 quality system, with TÜV SÜD audited manufacturing processes.

Send us your enquiry with the TRIO part number(s) or the equipment serial number and we will provide a quotation within 24 hours. Drawings, forging records and UT / MPI reports are available on request.

Related TC84X Assemblies

• TRIO17001222 — MAIN FRAME ASSEMBLY (chapter 1.1)
• TRIO17001205 — UPPER FRAME ASSEMBLY (chapter 1.2)
• TRIO17078213 — COUNTERSHAFT BOX ASSEMBLY (chapter 1.3)
• TRIO17001236 — SOCKET ASSEMBLY (chapter 1.4)
• TRIO17001188 — ECCENTRIC ASSEMBLY SHORT HEAD (chapter 1.5)
• TRIO5007838 — BOWL ASSEMBLY, SHF, TC84X (chapter 1.7)

Each sub-assembly can be quoted and supplied separately. CASTEEL MiningSpares holds ready stock of common TC84X wear and structural parts. Send us your parts list for a prompt quotation.

The post TRIO17001140 Main Shaft Assembly For TC84X Cone Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Equipment Overview

The TRIO CT4254 is a heavy-duty single-toggle jaw crusher widely used in mining, quarrying, aggregate production, and recycling for primary and secondary crushing of hard rock, ores, and demolition material. Its robust cast-steel frame and high-inertia eccentric shaft deliver consistent throughput under continuous duty.

The crushing chamber is formed by two opposing wear surfaces — the fixed jaw (stationary) and the swing jaw (reciprocating). Material is compressed and fractured between them on every stroke. Surrounding these liners, a set of supporting and clamping components keeps the wear parts seated, aligned, and tensioned so the crusher runs safely at full capacity. The seven parts listed below cover the complete wear and structural interface set for the CT4254 jaw module:

• Fixed Jaw & Swing Jaw – the primary crushing surfaces (manganese liners).
• Wedge Die, Swing (LH/RH) – clamps and locks the swing jaw liner to the swing jaw body.
• Upper / Lower Cheek Plates (RH/LH) – side liners that protect the crusher frame from abrasion.
• Wedge Block (TRIO17003948) – the hold-down / tension component that maintains liner position and crushing gap.

Available Parts List

Material & Manufacturing

All wear liners in this set are produced from high-manganese steel (Mn13 / Mn18Cr2) selected for its work-hardening behaviour — the surface grows harder under impact, giving excellent abrasion resistance in hard-rock service. Cheek plates and wedge components use cast carbon / low-alloy steel with precision machining for accurate fit.

Manufacturing follows a controlled process route:

1. Pattern & casting – resin sand moulding with controlled chemistry and pouring.
2. Heat treatment – water quenching and tempering to develop the required hardness and toughness.
3. Machining & inspection – critical faces and bolt holes machined to drawing; dimensions, hardness, and surface checked.
4. QC release – only parts passing inspection are packed and shipped.

OEM Quality Assurance

• Built to Original Specifications – manufactured to TRIO CT4254 drawings for 100% interchangeability with the genuine parts.
• Material Traceability – heat / batch numbers recorded; material test reports available on request.
• Strict Quality Control – dimensional, hardness, and surface inspection on every batch before release.
• Field-Proven Reliability – supplied to mining and aggregate operations across multiple continents.

Inquiry, Lead Time & Warranty

• Pricing – quote provided on inquiry; volume and repeat-order discounts available.
• Lead Time – typical 2–4 weeks depending on quantity and current foundry schedule.
• Shipping – seaworthy export packaging; worldwide delivery by sea or air.
• Warranty – 12 months against manufacturing defects.
• Customization – non-standard sizes, materials, or drawings can be produced on request.

FAQ

Q: Are these parts interchangeable with the original TRIO CT4254?
A: Yes. All parts are manufactured to original equipment drawings and are fully interchangeable with genuine TRIO CT4254 components.

Q: What is the typical lead time?
A: Standard items ship in 2–4 weeks; urgent orders can be discussed case by case.

Q: Can you supply parts to our own drawings or specifications?
A: Yes. We produce both standard and custom wear parts; send your drawing, sample, or part number and we will quote.

Q: Do you provide technical support for installation?
A: Yes. Layout drawings and fitting guidance are available; our engineers can advise on liner change-out and chamber setup.

Request a Quote for TRIO CT4254 Parts

.parts-table { width:100%; border-collapse:collapse; margin:16px 0; }
.parts-table th, .parts-table td { border:1px solid #ddd; padding:8px 10px; text-align:left; vertical-align:top; }
.parts-table th { background:#f5f5f5; font-weight:600; }
.parts-table tr:nth-child(even) { background:#fafafa; }
.button { display:inline-block; background:#c0392b; color:#fff !important; padding:12px 24px; border-radius:4px; text-decoration:none; font-weight:600; }
@media (max-width:768px) { .parts-table { display:block; overflow-x:auto; white-space:nowrap; } }

The post Full Set of Jaw Plates Cheek plates Wedges For CT4254 Jaw appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Product Overview

The TRIO17088016 Chain Assembly is the core traction component of the TAF1818 apron feeder, responsible for driving the feeder pan and conveying bulk materials. This assembly is precision-engineered to withstand high tensile loads, abrasive wear, and shock impact typical in mining, aggregate, and mineral processing applications. With a unit weight of 27,779.1 kg, it is a substantial heavy-duty component designed for continuous-duty operation.

Especificaciones

Key Features

Aplicaciones

• Mining & mineral processing — primary crusher feed
• Aggregate & quarry operations — material transfer
• Cement plants — clinker and raw material handling
• Heavy-duty bulk material conveying in harsh environments

Related TAF Series Parts

This chain assembly is part of our complete TRIO TAF Series Apron Feeder spare parts program covering TAF1808, TAF1818, and TAF1809 models — including rollers, sprockets, shafts, bearings, gearboxes, and more.

Browse the full parts list: TRIO TAF Series Apron Feeder Spare Parts Catalog →

The post TRIO17088016 Chain Assembly for TAF1818 Apron Feeder appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Featured: TRIO17088016 Chain Assembly

Heavy-duty chain assembly for TAF1818 apron feeder. Unit weight 27,779.1 kg. OEM-compatible direct-fit replacement with hardened pins and bushings for extended wear life.

View Product Details →

MiningSpares supplies direct-fit replacement parts for the full range of TRIO TAF Series Apron Feeders. All parts are manufactured to exact OEM specifications, ensuring interchangeability and reliable performance. Browse the parts list by model below and contact us for pricing.

TAF1808 Spare Parts — 1 Items

TAF1818 Spare Parts — 4 Items

TAF1809 Spare Parts — 28 Items

The post TRIO TAF Series Apron Feeder Spare Parts appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.