Product Overview

Matched wear parts for the CH440 / H4800 cone crusher: the 440 concave (442.8421) and the B-profile mantle (442.7230). Both are cast in M7 high manganese steel and machined on the seating and clamping faces so the cone head and upper frame locate correctly, keeping the closed-side setting and chamber geometry within specification.

Wear Parts List

Material and Casting

• M7 high manganese steel — the M7 grade is a work-hardening austenitic manganese casting (Mn18Cr2 type) that develops a hard wearing surface under load while the core stays tough enough to pass tramp metal. The grade is stamped on each casting for traceability.
• Water-glass sand casting with controlled heat treatment for a uniform austenitic structure.
• Machined seating and clamping faces so the concave beds down square in the frame and the mantle seats correctly on the cone head.
• B-profile cavity geometry matched to the original chamber specification.

Приложения

Suited to secondary and tertiary crushing of granite, basalt, limestone, river gravel, iron ore and construction and demolition waste. Replacing mantle and concave as a matched set avoids eccentric wear and keeps the setting stable through the wear cycle.

Request a Quotation

For pricing and lead time on the CH440 / H4800 wear parts (442.8421 concave and 442.7230 mantle B) in M7 material, use the Добавить в запрос button or email [email protected].

The post 442.8421 Concave Ring 442.7230 Mantle B for CH440 H4800 Cone Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Product Overview

A matched pair of crushing jaws for the QJ341 mobile jaw crusher (C12 jaw unit): the corrugated swing jaw (J2950000) and the stationary jaw plate (400.0436). Both are cast in M7 high manganese steel and machined on the seating faces so they pull down flat against the jaw stock and frame, keeping the crushing gap and nip angle within specification.

The corrugated profile on the swing jaw works against the stationary plate to grip and compress the feed, so the two faces wear as a pair. Supplying them together keeps the tooth profiles matched and the reduction ratio consistent through the wear cycle.

Wear Parts List

Equipment Overview

The QJ341 is a track-mounted mobile jaw crusher built around a single-toggle C12 jaw unit, widely used as a primary crusher in quarrying, mining, demolition and recycling. Material is fed between a stationary jaw plate fixed to the crusher frame and a swing jaw carried on the jaw stock, driven by the eccentric shaft. Tooth geometry and jaw profile control the nip angle, throughput and the shape of the primary product, so worn plates directly affect both capacity and downstream screening efficiency.

Material and Casting

• M7 high manganese steel — the M7 grade is a work-hardening austenitic manganese casting (Mn18Cr2 type) that develops a hard wearing surface under impact while the core remains tough enough to pass uncrushable material. The grade is stamped on each casting for traceability.
• Water-glass sand casting with controlled heat treatment to produce a uniform austenitic structure.
• Machined seating faces and matched bolt-hole pattern so both jaws bed down correctly and the wedges load evenly.
• Corrugated tooth profile matched to the original jaw geometry for correct nip and grip on slabby or rounded feed.

Приложения

Suited to primary crushing in hard rock quarries, mining operations, construction and demolition recycling, and aggregate production — granite, basalt, limestone, river gravel and demolition debris. Jaw wear life depends on feed size, material abrasiveness and the closed-side setting; fitting the swing and stationary jaws as a matched pair keeps both faces wearing evenly.

Related Parts Available

• CJ411 toggle plate and toggle seat for the same jaw crusher family
• CJ411 wedge plate (fixed / swing, 4 pcs per set)
• Swing and stationary jaw plates for other mobile jaw crushers in M7 (Mn18Cr2) and Mn22Cr2 grades

Request a Quotation

For pricing, lead time and availability on the QJ341 jaw wear parts (J2950000 corrugated swing jaw and 400.0436 stationary jaw plate) in M7 material, please use the Добавить в запрос button on this page or email us at [email protected]. Our sales team responds within one business day.

The post J2950000 Swing Jaw Corrugated 400.0436 Stationary Jaw Plate for QJ341 Mobile Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Product Overview

High manganese steel wear parts for the MCO9 mobile cone crusher: the Mantle STD (2295672) and the matching Torch Ring (2545973). The mantle is the moving crushing member mounted on the cone head, and the torch ring sits beneath it retaining and sealing the mantle assembly on the head — the two parts are normally replaced together during a liner change.

Wear Parts List

Equipment Overview

The MCO9 is a mobile cone crusher used as a secondary or tertiary stage in aggregate production, quarrying and recycling. Material is crushed between the mantle, which gyrates on the cone head, and the stationary bowl liner in the upper frame. Because the mantle carries the moving side of the crushing action, its wear profile controls the closed-side setting and the finished product shape — a worn mantle widens the gap locally and produces oversize and flaky material.

Material and Casting

• Mn18Cr2 high manganese steel — work-hardening austenitic manganese casting, giving a hard wearing surface under load with a tough core to survive tramp metal.
• Water-glass sand casting followed by controlled heat treatment for a consistent austenitic structure.
• Machined seating faces so the mantle pulls down square on the cone head and the torch ring beds correctly without rocking.
• Profile matched to the standard (STD) cavity for correct nip angle and throughput.

Приложения

Suited to secondary and tertiary crushing of granite, basalt, limestone, river gravel, iron ore and construction and demolition waste. Wear life depends on feed grading, the closed-side setting and the abrasiveness of the rock; replacing the mantle and the torch ring as a set avoids the sealing and retention problems that arise from mixing new and worn components.

Related Parts Available

• MCO9 cone crusher bowl liner and concave ring
• Mantle, bowl liner, concave and torch ring for other mobile cone crushers
• Cone crusher wear parts in Mn14Cr2, Mn18Cr2 and Mn22Cr2 grades

Request a Quotation

For pricing, lead time and availability on the MCO9 cone crusher wear parts (2295672 mantle STD and 2545973 torch ring), please use the Добавить в запрос button on this page or email us at [email protected]. Our sales team responds within one business day.

The post MCO9 Cone Crusher Wear Parts Mantle STD and Torch Ring Mn18Cr2 Casting appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Product Overview

This is a complete jaw wear parts set for the MC110R EVO and MC110Z EVO mobile jaw crushers, comprising the fixed crusher jaw, the moving crusher jaw and a pair of lower cheek plates. Manufactured by MiningSpares in Mn18Cr2 high manganese steel, these are the components that form the crushing chamber and take the direct wear from the feed material — so they are the parts replaced on a routine maintenance interval.

The set is supplied as a matched group so that the fixed jaw, moving jaw and cheek plates seat correctly against the jaw stock and frame, keeping the crushing gap and the jaw closing geometry within specification.

Wear Parts List

Equipment Overview

The MC110R EVO / MC110Z EVO is a mobile jaw crusher used as a primary crusher in demolition and recycling, natural stone processing, and quarrying. The machine uses a single-toggle jaw crusher unit with a hydraulically adjustable gap, fed by an independent vibrating feeder. The crushing chamber is lined by the fixed jaw (mounted on the crusher frame) and the moving jaw (carried on the jaw stock), with lower cheek plates closing the sides of the chamber. The toothed profile of both jaws grips and compresses the material, so tooth height and profile wear directly control the reduction ratio and the final product shape.

Material and Casting

• Mn18Cr2 high manganese steel — austenitic manganese casting that work-hardens rapidly under impact, developing a hard wear surface while the core stays tough enough to absorb uncrushable material.
• Water-glass sand casting with a controlled heat-treatment cycle to develop a uniform austenitic structure free from excessive carbides.
• Precision machining of the back face, bolt-hole pattern and wedge seating faces so the plates pull down flat against the jaw stock and frame.
• Tooth profile and pitch matched to the original jaw geometry for correct nip angle and throughput.

Приложения

Typical use includes construction and demolition waste recycling, asphalt and concrete recycling, natural rock crushing (granite, basalt, limestone, river gravel), and quarry primary crushing. The wear life of the fixed and moving jaws depends on feed size, material abrasiveness and the gap setting — a matched set keeps both jaws wearing evenly.

Related Parts Available

• Fixed and moving jaw 2419250 / 2419252 for MC110 Ri EVO
• MC110Z fixed jaw F10373201 and matching swing jaw
• Jaw plates, cheek plates, wedges and toggle components for other mobile jaw crushers

Request a Quotation

For pricing, lead time and availability on the MC110R EVO / MC110Z EVO jaw wear parts set (2419253 fixed jaw, 2419251 moving jaw, 2355334 / 2355337 lower cheek plates), please use the Добавить в запрос button on this page or email us at [email protected]. Our sales team responds within one business day.

The post MC110R EVO MC110Z EVO Jaw Crusher Wear Parts Set Fixed Jaw Moving Jaw and Cheek Plates Mn18Cr2 appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

High-manganese fixed and swing jaw plates manufactured by MiningSpares for the SAES CX120
European-type jaw crusher. SAES (Saes Makine Sanayi ve Ticaret A.Ş., Turkey) is an established
crushing and screening equipment manufacturer founded in 1992. The CX120 is their heavy-duty primary jaw crusher
designed for hard-rock quarrying and mining applications.

SAES CX120 Jaw Plate Specification Table

Material & Casting Process

All jaw plates are cast in Mn18% high-manganese steel (ASTM A128 Grade B2 equivalent)
using water-glass sand casting. Each plate undergoes solution heat treatment (water quenched) to achieve a fully
austenitic structure, then precision-machined on all mating surfaces for direct fitment into the SAES CX120 frame.
Key material properties:

• As-cast hardness: HB 200–220
• Work-hardened surface hardness in service: HB 450+
• Toughness: excellent impact resistance under high-compression crushing duty

Machine Data – SAES CX120 European Jaw Crusher

• Manufacturer: SAES (Saes Makine Sanayi ve Ticaret A.Ş., Turkey)
• Type: Heavy-duty primary jaw crusher (European type)
• Feed opening (width × depth): 1,200 × 870 mm
• Maximum feed lump size: 700 mm
• CSS (discharge setting) range: 70–200 mm (adjustable)
• Processing capacity: 175–610 t/h (material-dependent)
• Motor power: 160 kW (4-pole)
• Overall dimensions (L × W × H): 3,700 × 2,790 × 2,950 mm
• Drive: V-belt drive system with heavy flywheel inertia

Приложения

SAES CX120 jaw plates are designed for primary crushing of medium-hard to hard rock in quarrying,
aggregate production, mining and construction-recycling operations — granite, basalt, limestone, diabase
and similar abrasive materials up to 700 mm feed size.

Frequently Asked Questions

Q1. What is the standard material grade?
Mn18% high-manganese steel (equivalent to ASTM A128 Gr.B2). Mn18Cr2 and Mn13Cr2 grades are available
on request for highly abrasive or high-impact duties.

Q2. Can I buy individual plates?
Yes. The fixed jaw (30721010) and swing jaw (30701020) can be ordered separately.

Q3. What is the lead time?
Machined plates from stock: 7–10 working days. Fresh castings: 25–35 days. Breakdown orders
can be expedited with air freight.

Q4. What documentation is supplied?
Every shipment includes spectrometer chemical-composition report, hardness test report and dimensional
inspection report. Third-party inspection (SGS, BV, TÜV) available on request.

Q5. Is this an OEM part?
No. These are aftermarket replacement parts manufactured by MiningSpares to original drawing specifications.
Not affiliated with or endorsed by SAES Makine.

Request a Quotation

For pricing, lead time and alternative material options on SAES CX120 jaw plates, use the
Добавить в запрос button or email us at
[email protected]. Response within one business day.

The post 30721010 Fixed Jaw plate 30701020 Swing Jaw plate for SAES CX120 Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

High-manganese swing and fixed jaw plates manufactured by MiningSpares for the СМД-111
(SMD111) jaw crusher – the Russian-built primary jaw crusher also designated
ЩДП-9х12 and originally produced by Volgotsemmash (ОАО «Волгоцеммаш»).
The set consists of three cast manganese plates that form the primary crushing chamber: an upper and a lower
swing (movable) jaw plate running on the pitman, plus the stationary fixed jaw plate. Each plate is cast,
heat-treated and machined to drawing for direct replacement, with no frame modification required.

СМД-111 Jaw Plate Specification Table

Item 3 (3440.01.110) is a 2-piece (2P) fixed jaw plate design.

Material & Casting Process

All three plates are cast in Mn18% high-manganese steel (austenitic manganese steel,
equivalent to ASTM A128 Grade B2 / GOST 977-88 grade 110Г13Л) using water-glass sand casting. Each casting
is solution heat-treated (water quenched) to deliver a fully austenitic structure, then precision-machined on
all mating and seating faces so it seats correctly against the СМД-111 crusher frame and pitman.

• As-cast hardness: HB 200–220
• Work-hardened surface hardness in service: HB 450+
• Key benefit: the more the plate is impacted, the harder the working surface becomes –
  ideal for the high-compression duty of a primary jaw chamber

Machine Data – СМД-111 (ЩДП-9х12)

For fitment confirmation, the host machine data published by the original manufacturer:

• Designation: СМД-111 / ЩДП-9х12
• Feed opening (width × length): 900 × 1200 mm
• Maximum feed lump size: 750 mm
• Overall dimensions (L × W × H): 4,942 × 3,150 × 3,300 mm (excluding drive)
• Machine mass (less components): 54.3 t
• Application: primary crushing of granite, basalt, quartzite, sandstone, limestone and ores
  with a compressive strength up to 300 MPa

Приложения

СМД-111 jaw plates are used for primary crushing in hard-rock mining, quarry and aggregate production,
and construction-recycling duties – typically granite, gabbro, basalt and diabase duty in Russian and
CIS crushing plants.

Frequently Asked Questions

Q1. What material grade are the plates supplied in?
Mn18% high-manganese steel as standard. Mn18Cr2 and Mn13Cr2 are available on request for highly abrasive
or high-impact duties.

Q2. Can I buy a single plate rather than the full set?
Yes. Each of the three plates can be ordered separately – just quote the drawing number(s) from the table
above when enquiring.

Q3. What is the lead time?
Machined plates from stock: 7–10 working days. Fresh castings: 25–35 days. Breakdown orders can be
expedited and shipped by airfreight.

Q4. What documentation is supplied?
Every shipment includes spectrometer chemical-composition report, hardness test report and dimensional
inspection report. Third-party inspection (SGS, BV, TÜV) can be arranged on request.

Q5. Is this an OEM part?
No. These are aftermarket replacement parts manufactured by MiningSpares to the original drawings. They are
not affiliated with, or endorsed by, the original equipment manufacturer.

Request a Quotation

For pricing, lead time and alternative material grades on СМД-111 (SMD111) jaw plates, use the
Добавить в запрос button on this page or email us at
[email protected]. Our sales team responds within one business day.

The post 3440.02.010 / 3440.02.020 / 3440.01.110 Jaw Plates for Russian SMD111 Crusher appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

High manganese Mn18Cr2 fixed and swing jaw plates manufactured by MiningSpares for Metso Nordberg C106 jaw crushers. Each casting is produced in our own foundry, heat-treated for work-hardening performance and precision-machined on all mating faces to OEM specifications, providing a direct drop-in replacement for the original Metso parts.

Specification Table – Metso C106 Jaw Plate Set

About the Metso Nordberg C106 Jaw Crusher

The Metso Nordberg C106 is a compact primary jaw crusher designed for hard rock and recycle applications in mining, quarry and aggregate operations. With a 1060 × 700 mm (42 × 28 in) jaw opening, the C106 delivers high throughput in a small footprint and is widely used as a primary stage in both stationary and track-mounted plants. The key wear parts in the C106 are the fixed and swing jaw plates – the components that MiningSpares supplies in Mn18Cr2 high manganese steel under drawing numbers MM0273923 and MM0273924.

Why MiningSpares Metso C106 Jaw Plates

• Cast in our own foundry using premium Mn18Cr2 high manganese steel
• Heat treatment optimised for work-hardening under impact in primary crushing
• Precision machined to OEM drawing tolerances on back face and bolt-hole pattern
• Direct replacement for the original Metso parts MM0273923 and MM0273924
• Stock availability for standard C106 jaw plate sets in Mn18Cr2 grade
• Custom material grades available on request (Mn14, Mn22Cr2, modified manganese)

Compatible Equipment

Metso Nordberg C106 jaw crusher and similar Metso C-series primary jaw crushers. Drawing numbers covered on this page: MM0273923 (fixed jaw plate, 2 pieces per crusher set) and MM0273924 (swing jaw plate, 1 piece per crusher set).

Manufacturing Process

Our Metso C106 fixed and swing jaw plates are produced through water-glass sand casting, followed by a controlled heat treatment cycle to develop the work-hardening austenitic manganese structure. Each plate is then precision-machined on the back face, bolt-hole pattern and edge profile to ensure a perfect fit with the C106 jaw crusher frame and to match the original swing geometry of the machine.

Приложения

Metso C106 jaw plates are used in primary crushing of granite, basalt, gneiss, quartzite, iron ore, copper ore, gold ore, limestone and other medium-hard to hard rock. Typical installations include hard rock mining operations, quarries, aggregate production, and construction and demolition recycling.

Related Crusher Wear Parts

Browse more high manganese crusher wear parts from MiningSpares:

• PYB1200 Bowl Liner and Mantle
• MX4 Bowl Liner C for Cone Crusher
• Гидроконус H8800
• Boratas SDK111 Jaw Plate Wear Parts

Request a Quotation

For pricing, lead time and material options on Metso C106 jaw plates MM0273923 and MM0273924, please use the Добавить в запрос button on this page or email us at [email protected]. Our sales team will respond within one business day.

The post MM0273923 Fixed Jaw Quarry MM0273924 Swing Jaw Quarry For C106 Jaw appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Items: Concave, Mantle, Concave Ring, Concave Segment, Bowl Liner, Cone Liner, Arm Guard, Distribution Plate
Casting Material: Austenitic Manganese Steel (Mn14, Mn14Cr2, Mn18Cr2, Mn22Cr2)
Метод литья: Литье в песок из водного стекла
Applicable Material: Gravel, Granite, Basalt, Ore, Limestone, Sandstone, Quartz, Cobblestone
Applications: Mining, Quarry, Construction, Cement and Materials, Recycling

MiningSpares’ Cedarapids RC54 Bowl Liner and Mantle uses high-quality manganese alloys, including 13% Standard, 18% Premium, and 22% High alloys, to cater to diverse operational requirements and can be customized according to your needs
У нас также есть различные цвета для вас, чтобы выбрать из, красный, синий, зеленый, черный, серый и так далее

Rollercone RC54 Mantle & Bowl Liner Specifications

The manufacturing process is very rigorous to ensure a perfect fit with the Cedarapids RC54 Cone Crusher.

Our Rollercone RC54 Mantle & Bowl Liner wear parts are manufactured using advanced casting processes. During the manufacturing process, we strictly control material selection and process flow to ensure excellence in product quality and performance. We use high-quality alloy steel materials, combined with advanced casting technology, to ensure that the wear parts have excellent wear resistance and impact resistance. In addition, our production process includes precision machining and heat treatment processes to further improve the strength and durability of the liners.

For most of the world famous brands like Metso, Sandvik, Terex, Shanbao, Telsmith and so on
У каждого из нас есть большой запас оригинальных рисунков, что помогает нам производить продукцию по относительно низкой цене.

Related Cone Crusher Wear Parts

Browse more high manganese cone crusher wear parts from MiningSpares:

• PYB1200 Bowl Liner and Mantle
• MX4 Bowl Liner C for Cone Crusher
• Гидроконус H8800
• Cone Crusher Wear Parts BG00523226

The post EL-Jay Rollercone RC54 Cone Crusher Wear Parts – Mantle & Bowl Liner appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

Equipment Overview

The TRIO CT4254 is a heavy-duty single-toggle jaw crusher widely used in mining, quarrying, aggregate production, and recycling for primary and secondary crushing of hard rock, ores, and demolition material. Its robust cast-steel frame and high-inertia eccentric shaft deliver consistent throughput under continuous duty.

The crushing chamber is formed by two opposing wear surfaces — the fixed jaw (stationary) and the swing jaw (reciprocating). Material is compressed and fractured between them on every stroke. Surrounding these liners, a set of supporting and clamping components keeps the wear parts seated, aligned, and tensioned so the crusher runs safely at full capacity. The seven parts listed below cover the complete wear and structural interface set for the CT4254 jaw module:

• Fixed Jaw & Swing Jaw – the primary crushing surfaces (manganese liners).
• Wedge Die, Swing (LH/RH) – clamps and locks the swing jaw liner to the swing jaw body.
• Upper / Lower Cheek Plates (RH/LH) – side liners that protect the crusher frame from abrasion.
• Wedge Block (TRIO17003948) – the hold-down / tension component that maintains liner position and crushing gap.

Available Parts List

Material & Manufacturing

All wear liners in this set are produced from high-manganese steel (Mn13 / Mn18Cr2) selected for its work-hardening behaviour — the surface grows harder under impact, giving excellent abrasion resistance in hard-rock service. Cheek plates and wedge components use cast carbon / low-alloy steel with precision machining for accurate fit.

Manufacturing follows a controlled process route:

1. Pattern & casting – resin sand moulding with controlled chemistry and pouring.
2. Heat treatment – water quenching and tempering to develop the required hardness and toughness.
3. Machining & inspection – critical faces and bolt holes machined to drawing; dimensions, hardness, and surface checked.
4. QC release – only parts passing inspection are packed and shipped.

OEM Quality Assurance

• Built to Original Specifications – manufactured to TRIO CT4254 drawings for 100% interchangeability with the genuine parts.
• Material Traceability – heat / batch numbers recorded; material test reports available on request.
• Strict Quality Control – dimensional, hardness, and surface inspection on every batch before release.
• Field-Proven Reliability – supplied to mining and aggregate operations across multiple continents.

Inquiry, Lead Time & Warranty

• Pricing – quote provided on inquiry; volume and repeat-order discounts available.
• Lead Time – typical 2–4 weeks depending on quantity and current foundry schedule.
• Shipping – seaworthy export packaging; worldwide delivery by sea or air.
• Warranty – 12 months against manufacturing defects.
• Customization – non-standard sizes, materials, or drawings can be produced on request.

FAQ

Q: Are these parts interchangeable with the original TRIO CT4254?
A: Yes. All parts are manufactured to original equipment drawings and are fully interchangeable with genuine TRIO CT4254 components.

Q: What is the typical lead time?
A: Standard items ship in 2–4 weeks; urgent orders can be discussed case by case.

Q: Can you supply parts to our own drawings or specifications?
A: Yes. We produce both standard and custom wear parts; send your drawing, sample, or part number and we will quote.

Q: Do you provide technical support for installation?
A: Yes. Layout drawings and fitting guidance are available; our engineers can advise on liner change-out and chamber setup.

Request a Quote for TRIO CT4254 Parts

.parts-table { width:100%; border-collapse:collapse; margin:16px 0; }
.parts-table th, .parts-table td { border:1px solid #ddd; padding:8px 10px; text-align:left; vertical-align:top; }
.parts-table th { background:#f5f5f5; font-weight:600; }
.parts-table tr:nth-child(even) { background:#fafafa; }
.button { display:inline-block; background:#c0392b; color:#fff !important; padding:12px 24px; border-radius:4px; text-decoration:none; font-weight:600; }
@media (max-width:768px) { .parts-table { display:block; overflow-x:auto; white-space:nowrap; } }

The post Full Set of Jaw Plates Cheek plates Wedges For CT4254 Jaw appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.

The post Fixed and Swing Crushing Jaw 2419250 2419252 suit Kleemann MC11O Ri EVO appeared first on Mining Spares | Crusher Spare Parts ,Drifter Parts ,Slurry Pump Parts.